Suspension & Steering

Hub-center steering (HCS) is one of several different types of front end suspension/steering mechanisms used in motorcycles. Hub-center steering is characterized by a swingarm that extends from the bottom of the engine/frame to the centre of the front wheel instead of two forks. more...

Home
ATV Parts
Apparel & Merchandise
Automotive Tools
Aviation Parts
Boat Parts
Car & Truck Parts
Air Conditioning and Heat
Air Intake & Fuel Delivery
Brakes
Charging & Starting Systems
Computer, Chip, Cruise...
Cooling System
Decals, Emblems, & Detailing
Emission System
Engines & Components
Exhaust
Exterior
Filters
Gaskets
Gauges
Glass
Ignition System
Interior
Lighting & Lamps
Other Parts
Safety & Security
Salvage Parts Cars
Suspension & Steering
Ball Joints
Caster/Camber Kits
Coil Springs
Control Arms & Parts
Leaf Springs
Lift Kits & Parts
Lower Kits & Parts
Other
Pitman & Idler Arms
Power Steering Pumps & Parts
Shocks & Struts
Steering Racks & Gear Boxes
Strut Bars
Sway Bars
Tie Rod Linkages
Transmission & Drivetrain
Turbos, Nitrous,...
Wheels, Tires & Parts
Car Audio, Video
Manuals & Literature
Motorcycle Parts
Other Vehicle Parts
Personal Watercraft Parts
Racing Parts
Services & Installation
Snowmobile Parts
Vintage Car & Truck Parts
Wholesale Lots

The advantages of using a hub-center steering system instead of a more conventional motorcycle fork are that hub-center steering separates the steering, braking, and suspension functions.

With a fork the braking forces are put through the suspension, a situation that leads to the suspension being compressed, using up a large amount of suspension travel which makes dealing with bumps and other road irregularities extremely difficult. As the forks dive the steering geometry of the bike also changes making the bike more nervous, and inversely on acceleration becomes more lazy. Also, having the steering working through the forks causes problems with stiction, decreasing the effectiveness of the suspension. The length of the typical motorcycle fork means that they act as large levers about the headstock requiring the forks, the headstock, and the frame to be very robust adding to the bikes weight.

Hub-center steering systems use an arm, or arms, on bearings to allow upward wheel deflection, meaning that there is no stiction, even under braking. Braking forces can be redirected horizontally along these arms (or tie rods) away from the vertical suspension forces, and can even be put to good use to counteract weight shift. Finally, the arms typically form some form of parallelogram which maintains steering geometry over the full range of wheel travel, allowing agility and consistency of steering that forks currently cannot get close to attaining. The hub center steering's achilles heel, however, has been steering feel. Complex linkages tend to be involved in the steering process, and this can lead to slack, vague, or inconsistent handlebar movement across its range.

Hub-center steering systems have only appeared on a very few production motorcycles, and not with any great success. Evolution, rather than revolution, tends to drive advancements in new models, and dictate sales. After so many years of telescopic forks, people are used to riding a bike that handles in a specific way, and almost expect the limitations, and compensation is part of the experience. Also there is a depth of knowledge known about fork based chassis design that attempts each year to get around the limitations through technological advances on the current system. Thicker and thicker fork tubes are used to reduce flex, special coatings are used to aid stiction, and greater and greater steering angles are used to counteract dive.

The hub-center steer concept is a very old one used as early as 1920 by Ner-a-car, and enjoyed an aftermarket vogue in the 1970's through the work of Jack Difazio in the UK. Then in the 1980's Elf created a succession of GP race bikes. In the 90's there was a flurry of action, first was the Bimota Tesi 1D in 1991 (designed by a young Massimo Tamburini of 916 fame) however this was expensive and was only ever produced in small numbers. Then in 1993 Yamaha launched the GTS1000 based on James Parker's RADD design. It raced at the Isle of Man TT but was always blighted with a reputation for being a bit heavy and clumsy in use. In 1995 Michael Tryphonos built a prototype based on the Defazio system that did race at the isle of man with some success reaching 11th in the Senior TT.

Read more at Wikipedia.org